PP3LS01 - Power Probe III Tester with Leadset Kit
Product Description
#PP3LS01 - Kit Includes: Power Probe III, Cigarette Lighter Adapter, 3" Probe Tip, Battery Hook Up Clips, 20FT Extension Lead, 2 Piercing Probes, Male & Female Adapters, Alligator Clip Adapter, 1-3-6 Foot Leads, Instruction Manual & Blow Mold Case
** VERY IMPORTANT NOTE: COMBO KITS AND MASTER KITS DO NOT OFFER COLOR CHOICE FOR POWER PROBE **
---------------------------------------------------------------
Power Probe III
Maximum Voltage on Probe Tip: ± 200 Volts Relative to the Negative Battery Clip Probe tip resistance to ground 130KΩ Computer Safe: 0.1mA floating tip(warning: do not press power switch while connected to computer circuits with PP1,2 or 3)
Power Probe Mode (Mode 1)
DC Voltage Measurement: 0 to 70 Volts (in 1/10th increments) AC Voltage Measurement: 0 to 70 Volts Peak to Peak (See Peak to Peak & Threshold Setting Mode 5)
Square Wave Input Response: 15 Hz to over 500KHz Sine Wave Input Response: 35 Hz to over 250KHz
Continuity to Ground: Greater than 20K Ohms - Display is Blank Less than 20K Ohms: Display reads 0.0 Less than 2K Ohms: Display reads 0.0 and Green Led is On
Min (Mode 2) & Max (Mode 3) Voltage Measurement: 0 to 70 Volts Single Event Capture: Less than 200 Micro Second Pulse Width Repetitive Events: Less than 1 Micro Second Pulse Width
Peak to Peak Mode (Mode 4) 0 to 70 Volts P-P Square Wave Input Response: 4 Hz to over 500KHz Sine Wave Input Response: 4 Hz to over 250KHz
Peak to Peak Mode Threshold Setting (Mode 5) 0.2, 0.5, 1, 2, 5, 10 & 50 When the Peak to Peak Voltage on the Probe Tip exceeds this threshold then the display is Peak to Peak AC rather than DC.
Storage temperature: -40°C (-40°F) to 70°C (158°F) Operating temperature -20°C (-4°F) to 60°C (140°F)
Circuit Breaker 8 amp thermal response - manual reset 8 amp=No trip 10 amps=20 min. 15 amps=6 sec. 25 amps=2 sec. Short circuit=0.3 sec.
** VERY IMPORTANT NOTE: COMBO KITS AND MASTER KITS DO NOT OFFER COLOR CHOICE FOR POWER PROBE **
---------------------------------------------------------------
Power Probe III
Maximum Voltage on Probe Tip: ± 200 Volts Relative to the Negative Battery Clip Probe tip resistance to ground 130KΩ Computer Safe: 0.1mA floating tip(warning: do not press power switch while connected to computer circuits with PP1,2 or 3)
Power Probe Mode (Mode 1)
DC Voltage Measurement: 0 to 70 Volts (in 1/10th increments) AC Voltage Measurement: 0 to 70 Volts Peak to Peak (See Peak to Peak & Threshold Setting Mode 5)
Square Wave Input Response: 15 Hz to over 500KHz Sine Wave Input Response: 35 Hz to over 250KHz
Continuity to Ground: Greater than 20K Ohms - Display is Blank Less than 20K Ohms: Display reads 0.0 Less than 2K Ohms: Display reads 0.0 and Green Led is On
Min (Mode 2) & Max (Mode 3) Voltage Measurement: 0 to 70 Volts Single Event Capture: Less than 200 Micro Second Pulse Width Repetitive Events: Less than 1 Micro Second Pulse Width
Peak to Peak Mode (Mode 4) 0 to 70 Volts P-P Square Wave Input Response: 4 Hz to over 500KHz Sine Wave Input Response: 4 Hz to over 250KHz
Peak to Peak Mode Threshold Setting (Mode 5) 0.2, 0.5, 1, 2, 5, 10 & 50 When the Peak to Peak Voltage on the Probe Tip exceeds this threshold then the display is Peak to Peak AC rather than DC.
Storage temperature: -40°C (-40°F) to 70°C (158°F) Operating temperature -20°C (-4°F) to 60°C (140°F)
Circuit Breaker 8 amp thermal response - manual reset 8 amp=No trip 10 amps=20 min. 15 amps=6 sec. 25 amps=2 sec. Short circuit=0.3 sec.
